CMIT 351: Project 2: Design and Implement a Routed LAN

CMIT 351 Project 2 Description


ACME University IT has reviewed the results from your prototype and now wants to move forward with
an adjusted set of requirements. You will need to implement layer 2 segmentation to control broadcast
domains and increase Local Area Network (LAN) performance but also provide routing between
segments.
Scenario
IT has tasked you with implementing the revised, routed LAN. This effort builds on the prototype you
recently completed. As always, you need to document all your work. The requirements you have specify a
maximum number of switches (1), the number of virtual LANs (VLANs) as four, one router, and some
computers in each VLAN for endpoint testing.
Overview
Modern switches use VLANs to improve network performance by separating large Layer 2 broadcast
domains into smaller ones. In general, VLANs make it easier to design a network to support the goals of
an organization. However, VLANs are not able to intercommunicate without the addition of Layer 3
routing. A router or similar capability is required to facilitate inter-VLAN communication. Additionally,
trunking will be required between network layers.
Objectives

  • Design a routed Local Area Network using switches, routers, and hosts (computers)
  • Describe basic switch configuration necessary for switch maintenance and operation
  • Describe basic router configuration necessary for router maintenance and operation
  • Describe Virtual LANs (VLANs) configurations to enforce segmentation
  • Describe router interface configuration necessary facilitate inter-VLAN routing
  • Describe necessary VLAN trunking between the switch and router
    Tools
  • Access to physical Cisco devices is not required to complete this project.
  • However, you will need the Cisco Packet Tracer educational tool as this project will be
    completed as a Cisco Packet Tracer Activity. (https://skillsforall.com/course/getting-started-ciscopacket-tracer)
  • You can reference the following uCertify labs for help in building the switch configuration
    narratives: Modules 5, 6, 7, 8, 9, 10, 15, and 17
    Submission
    Use the Project 2 Template MS Word to document screenshots and descriptive answers for your
    submission. Fundamentally, you need to attach/submit two things:
    a) The completed Cisco Packet Tracer activity file (do not forget to save the PKA file once you have
    completed the project activity before uploading)
    b) Screenshots and descriptive answers will go into the MS Word document “CMIT 351 Project 2
    Template”.
    Version 2.0
    Part 1: Design the Local Area Network
    The work milestones for this part of the project are as follows:
  • The total LAN must consist of 1 switch, 1 Router and 4 computers.
  • The switch must be named S1.
  • The router must be named R1.
  • The four computers must be named PC-A, PC-B, PC-C, and PC-D.
    Part 2: Create the basic switch and router configurations
    Your network engineering lead has approved the LAN design. Now, the work to implement the
    design can begin. Your tasks are as follows:
    2.1 Cable the network
  • Connect S1 Ethernet Interface 1 to R1 Ethernet Interface 1
  • Connect PC-A to S1 on Ethernet Interface 4
  • Connect PC-B to S1 on Ethernet Interface 6
  • Connect PC-C to S1 on Ethernet Interface 11
  • Connect PC-D to S1 on Ethernet Interface 13
    2.2. Configure the basic switch and router functions
    Configure the basic functions in S1 and R1 as follows:
  • Set the enable secret to “class”
  • Set the line con 0 password to “cisco”
  • Set the line vty 0 15 password to “cisco”
  • Set the MOTD to “Unauthorized access is strictly prohibited.”
  • Set logging to synchronous
    2.3 Configure the computers
    Configure the four computers as follows:
    Name IP Address Subnet Gateway
    PC-A 192.168.10.3 255.255.255.0 192.168.10.1
    PC-B 192.168.20.4 255.255.255.0 192.168.20.1
    PC-C 192.168.30.5 255.255.255.0 192.168.30.1
    PC-D 192.168.40.6 255.255.255.0 192.168.40.1
    2.4 Test and Validate Connectivity
    Use ping to test connectivity between the computers. Detail your results in your project
    document, both what works and what doesn’t work.
    Part 3: Define the VLANs
    3.1 You need to define four VLANs on the switch as follows:
    Version 2.0
  • VLAN 10 Students
  • VLAN 20 Faculty
  • VLAN 30 Management
  • VLAN 99 Containment
    3.2 Then, define the following interfaces for the VLANs as:
    Device Interfaces VLAN / IP Address
    S1 4 VLAN 10
    S1 6 VLAN 20
    S1 11 VLAN 30
    S1 2-3,5,7-10,12-24 VLAN 99
    R1 Ethernet Interface 1, subinterface 10 192.168.10.1 255.255.255.0
    R1 Ethernet Interface 1, subinterface 20 192.168.20.1 255.255.255.0
    R1 Ethernet Interface 1, subinterface 30 192.168.30.1 255.255.255.0
    Part 4: Implement VLAN Trunking
    4.1 Implement VLAN trunking on the switch as follows:
  • Manually set interface 1 on S1 to trunk (do not use mode dynamic desirable)
  • Manually set Interface 1, subinterface 10 on R1 for 802.1Q encapsulation in VLAN 10
  • Manually set Interface 1, subinterface 20 on R1 for 802.1Q encapsulation in VLAN 20
  • Manually set Interface 1, subinterface 30 on R1 for 802.1Q encapsulation in VLAN 30
    4.2 Use ping to test connectivity between the computers and switches. Detail your results in
    your project template document, both what works and what doesn’t work. Pay close
    attention to PC-D!

Answer Preview: CMIT 351: Project 2: Design and Implement a Routed LAN


Posted

in

by

Tags: